View 74HC4067BQ_8743541.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74hc4067; 74hct4067 is a high-speed si-g ate cmos device and is pin compatible with the hef4067b. the device is specified in compliance with jedec standard no. 7a. the 74hc4067; 74hct4067 is a 16-channel analog multiplexer/demultiplexer with four address inputs (s0 to s3), an active-low enable input (e ), sixteen independent inputs/outputs (y0 to y15) and a common input/output (z). the 74hc4067; 74hct4067 contains sixteen bidirectional analog switches, each with one side connected to an independent input/output (y0 to y15) and the other side connected to a common input/output (z). with pin e = low, one of the sixteen switches is selected by pins s0 to s3 (low impedance on-state). all unselected switch es are in the high-impedance off-state. with pin e = high, all switches are in the high-imp edance off-state, independent of pins s0 to s3. the analog inputs/outputs (y0 to y15, and z) can swing between v cc as a positive limit and gnd as a negative limit. v cc to gnd may not exceed 10 v. 2. features and benefits ? low on resistance: ? 80 ? (typical) at v cc = 4.5 v ? 70 ? (typical) at v cc = 6.0 v ? 60 ? (typical) at v cc = 9.0 v ? typical ?break before make? built-in 3. applications ? analog multiplexing and demultiplexing ? digital multiplexing and demultiplexing ? signal gating 74hc4067; 74hct4067 16-channel analog mult iplexer/demultiplexer rev. 5 ? 13 december 2011 product data sheet
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 2 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 4. ordering information table 1. ordering information type number package temperature range name description version 74hc4067 74hc4067n ? 40 ? c to +125 ? c dip24 plastic dual in-line package; 24 leads (600 mil); reverse bending sot101-1 74hc4067d ? 40 ? c to +125 ? c so24 plastic small outline package; 24 leads; body width 7.5 mm sot137-1 74hc4067db ? 40 ? c to +125 ? c ssop24 plastic shrink small outline package; 24 leads; body width 5.3 mm sot340-1 74hc4067pw ? 40 ? c to +125 ? c tssop24 plastic thin shrink small outline package; 24 leads; body width 4.4 mm sot355-1 74HC4067BQ ? 40 ? c to +125 ? c dhvqfn24 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 ? 5.5 ? 0.85 mm sot815-1 74hct4067 74hct4067n ? 40 ? c to +125 ? c dip24 plastic dual in-line package; 24 leads (600 mil); reverse bending sot101-1 74hct4067d ? 40 ? c to +125 ? c so24 plastic small outline package; 24 leads; body width 7.5 mm sot137-1 74hct4067db ? 40 ? c to +125 ? c ssop24 plastic shrink small outline package; 24 leads; body width 5.3 mm sot340-1 74hct4067pw ? 40 ? c to +125 ? c tssop24 plastic thin shrink small outline package; 24 leads; body width 4.4 mm sot355-1 74hct4067bq ? 40 ? c to +125 ? c dhvqfn24 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 ? 5.5 ? 0.85 mm sot815-1
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 3 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 5. functional diagram fig 1. logic symbol fig 2. iec logic symbol 001aag725 9 y0 8 10 y1 s0 11 s1 14 s2 13 s3 15 e 7 y2 6 y3 5 y4 4 y5 z 1 3 y6 2 y7 23 y8 22 y9 21 y10 20 y11 19 y12 18 y13 17 y14 16 y15 0 mux/dmux 3 9 g16 8 7 6 1 5 4 3 2 0 1 2 3 4 5 6 7 23 22 21 20 19 18 17 16 8 9 10 11 12 13 14 15 001aag726 16 0 15 10 11 14 13 15 fig 3. schematic diagram (one switch) 001aag729 yn z gnd from logic v cc v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 4 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 4. functional diagram 001aag727 1-of-16 decoder 10 9y0 s0 8y1 7y2 6y3 5y4 4y5 3y6 2y7 23 y8 22 y9 21 y10 20 y11 19 y12 18 y13 17 y14 16 y15 1z 11 s1 14 s2 13 s3 15 e
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 5 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 5. logic diagram 001aag728 y0 y1 s0 s1 s2 s3 e y2 y3 y4 y5 y6 y7 y8 y9 y10 y11 y12 y13 y14 y15 z
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 6 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 6. pinning information 6.1 pinning 6.2 pin description (1) this is not a supply pin. the substrate is attached to this pad using conductive die attach material. there is no electrical or mechani cal requirement to solder this pad. however, if it is soldered, the solder land should remain floating or be connected to v cc . fig 6. pin configuration fo r dip24, so24, ssop24 and tssop24 fig 7. pin configuration for dhvqfn24 74hc4067 74hct4067 zv cc y7 y8 y6 y9 y5 y10 y4 y11 y3 y12 y2 y13 y1 y14 y0 y15 s0 e s1 s2 gnd s3 001aag730 1 2 3 4 5 6 7 8 9 10 11 12 14 13 16 15 18 17 20 19 22 21 24 23 001aag731 74hc4067 74hct4067 transparent top view s2 s0 s1 e y0 y15 y1 y14 y2 y13 y3 y12 y4 y11 y5 y10 y6 y9 y7 y8 gnd s3 z v cc 11 14 10 15 9 16 8 17 7 18 6 19 5 20 4 21 3 22 2 23 12 13 1 24 terminal 1 index area v cc (1) table 2. pin description symbol pin description z 1 common input or output y7, y6, y5, y4, y3, y2, y1, y0, y15, y14, y13, y12, y11, y10, y9, y8 2, 3, 4, 5, 6, 7, 8, 9, 16, 17, 18, 19, 20, 21, 22, 23 indep endent input or output s0, s1, s3, s2 10, 11, 13, 14 address input 0 gnd 12 ground (0 v) e 15 enable input (active low) v cc 24 supply voltage
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 7 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 7. functional description [1] h = high voltage level; l = low voltage level; x = don?t care. 8. limiting values table 3. function table [1] inputs channel on e s3 s2 s1 s0 llllly0 to z llllhy1 to z lllhly2 to z lllhhy3 to z l l h l l y4 to z l l hl hy5 to z l l h h l y6 to z l l hhhy7 to z lhllly8 to z l h l l h y9 to z lhlhly10 to z l h l h h y11 to z l hhl l y12 to z l hhl hy13 to z l hhhl y14 to z l hhhhy15 to z hxxxx- table 4. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage [1] ? 0.5 +11.0 v i ik input clamping current v i < ? 0.5 v or v i >v cc +0.5v - ? 20 ma i sk switch clamping current v sw < ? 0.5 v or v sw >v cc +0.5v - ? 20 ma i sw switch current v sw = ? 0.5 v to v cc +0.5v - ? 25 ma i cc supply current - 50 ma i gnd ground current - ? 50 ma t stg storage temperature ? 65 +150 ?c
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 8 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer [1] to avoid drawing v cc current out of terminal z, when switch current flows in terminals yn, the voltage drop across the bidirectional switch must not exceed 0.4 v. if the switch current flows into terminal z, no v cc current will flow out of terminals yn. in this case there is no limit for the voltage drop across the switch, but the voltages at yn and z may not exceed v cc or gnd. [2] for dip24 package: p tot derates linearly with 12 mw/k above 70 ? c. [3] for so24 package: p tot derates linearly with 8 mw/k above 70 ? c. [4] for ssop24 and tssop24 packages: p tot derates linearly with 5.5 mw/k above 60 ? c. [5] for dhvqfn24 package: p tot derates linearly with 4.5 mw/k above 60 ? c. 9. recommended operating conditions p tot total power dissipation t amb = ? 40 ? c to +125 ?c dip24 package [2] -750mw so24 package [3] -500mw ssop24 package [4] -500mw tssop24 package [4] -500mw dhvqfn24 package [5] -500mw p power dissipation per switch - 100 mw table 4. limiting values ?continued in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit table 5. recommended operating conditions symbol parameter conditions min typ max unit 74hc4067 v cc supply voltage 2.0 5.0 10.0 v v i input voltage gnd - v cc v v sw switch voltage gnd - v cc v ? t/ ? v input transition rise and fall rate v cc = 2.0 v - - 625 ns v cc = 4.5 v - 1.67 139 ns v cc =6.0v - - 83 ns v cc = 10.0 v - - 31 ns t amb ambient temperature ? 40 +25 +125 ?c 74hct4067 v cc supply voltage 4.5 5.0 5.5 v v i input voltage gnd - v cc v v sw switch voltage gnd - v cc v ? t/ ? v input transition rise and fall rate v cc = 4.5 v - 1.67 139 ns t amb ambient temperature ? 40 +25 +125 ?c
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 9 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 10. static characteristics [1] at supply voltages (v cc ? gnd) approaching 2 v, the analog switch on resist ance becomes extremely non-linear. therefore it is recommended that these devices be used to transmit di gital signals only, when us ing these supply voltages. table 6. r on resistance per switch for types 74hc4067 and 74hct4067 v i = v ih or v il ; for test circuit see figure 8 . v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. for 74hc4067: v cc ? gnd = 2.0 v, 4.5 v, 6.0 v and 9.0 v. for 74hct4067: v cc ? gnd = 4.5 v. symbol parameter conditions 25 ?c ? 40 ? c to +125 ?c unit typ max max (85 ?c) max (125 ?c) r on(peak) on resistance (peak) v is = v cc to gnd v cc = 2.0 v; i sw = 100 ? a [1] ---- ? v cc = 4.5 v; i sw = 1000 ? a 110 180 225 270 ? v cc = 6.0 v; i sw = 1000 ? a 95 160 200 240 ? v cc = 9.0 v; i sw = 1000 ? a 75 130 165 195 ? r on(rail) on resistance (rail) v is = gnd or v cc v cc = 2.0 v; i sw = 100 ? a [1] 150--- v cc = 4.5 v; i sw = 1000 ? a 90 160 200 240 ? v cc = 6.0 v; i sw = 1000 ? a 80 140 175 210 ? v cc = 9.0 v; i sw = 1000 ? a 70 120 150 180 ? ? r on on resistance mismatch between channels v is = v cc to gnd v cc = 2.0 v [1] ---- ? v cc = 4.5v 9--- ? v cc = 6.0v 8--- ? v cc = 9.0v 6--- ?
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 10 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer v is = 0 v to (v cc ? gnd) v is = 0 v to (v cc ? gnd) (1) v cc = 4.5 v (2) v cc = 6.0 v (3) v cc = 9.0 v fig 8. test circuit for measuring r on fig 9. typical r on as a function of input voltage v is 001aag733 v il z v cc yn e i sw v is gnd v sw v is (v) 0 9.0 7.2 3.6 5.4 1.8 mnb047 50 70 30 90 110 10 r on () (1) (2) (3) r on v sw i sw --------- - = table 7. static characteristics 74hc4067 at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v). v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 ?c v ih high-level input voltage v cc = 2.0 v 1.5 1.2 - v v cc = 4.5 v 3.15 2.4 - v v cc = 6.0 v 4.2 3.2 - v v cc = 9.0 v 6.3 4.7 - v v il low-level input voltage v cc = 2.0 v - 0.8 0.5 v v cc = 4.5 v - 2.1 1.35 v v cc = 6.0 v - 2.8 1.80 v v cc = 9.0 v - 4.3 2.70 v i i input leakage current v i = v cc or gnd v cc = 6.0 v - - ? 0.1 ? a v cc = 10.0 v - - ? 0.2 ? a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 0.1 ? a all channels - - ? 0.8 ? a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 -- ? 0.8 ? a
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 11 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd v cc = 6.0 v - - 8.0 ? a v cc = 10.0 v - - 16.0 ? a c i input capacitance - 3.5 - pf t amb = ? 40 ?c to +85 ?c v ih high-level input voltage v cc = 2.0 v 1.5 - - v v cc = 4.5 v 3.15 - - v v cc = 6.0 v 4.2 - - v v cc = 9.0 v 6.3 - - v v il low-level input voltage v cc = 2.0 v - - 0.50 v v cc = 4.5 v - - 1.35 v v cc = 6.0 v - - 1.80 v v cc = 9.0 v - - 2.70 v i i input leakage current v i = v cc or gnd v cc = 6.0 v - - ? 1.0 ? a v cc = 10.0 v - - ? 2.0 ? a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 1.0 ? a all channels - - ? 8.0 ? a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 -- ? 8.0 ? a i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd v cc = 6.0 v - - 80.0 ? a v cc = 10.0 v - - 160 ? a t amb = ? 40 ? c to +125 ?c v ih high-level input voltage v cc = 2.0 v 1.5 - - v v cc = 4.5 v 3.15 - - v v cc = 6.0 v 4.2 - - v v cc = 9.0 v 6.3 - - v v il low-level input voltage v cc = 2.0 v - - 0.50 v v cc = 4.5 v - - 1.35 v v cc = 6.0 v - - 1.80 v v cc = 9.0 v - - 2.70 v i i input leakage current v i = v cc or gnd v cc = 6.0 v - - ? 1.0 ? a v cc = 10.0 v - - ? 2.0 ? a table 7. static characteristics 74hc4067 ?continued at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v). v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 12 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 1.0 ? a all channels - - ? 8.0 ? a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 -- ? 8.0 ? a i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd v cc = 6.0 v - - 160 ? a v cc = 10.0 v - - 320 ? a table 7. static characteristics 74hc4067 ?continued at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v). v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit table 8. static characteristics 74hct4067 at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v). v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 ?c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 1.6 - v v il low-level input voltage v cc = 4.5 v to 5.5 v - 1.2 0.8 v i i input leakage current v i = v cc or gnd; v cc = 5.5 v - - ? 0.1 ? a i s(off) off-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 0.1 ? a all channels - - ? 0.8 ? a i s(on) on-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 --? 0.8 ? a i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd; v cc = 4.5 v to 5.5 v --8.0 ? a ? i cc additional supply current per input pin; v i = v cc ? 2.1 v; other inputs at v cc or gnd; v cc = 4.5 v to 5.5 v pin e - 60 216 ? a pin sn - 50 180 ? a c i input capacitance - 3.5 - pf t amb = ? 40 ?c to +85 ?c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 - - v v il low-level input voltage v cc = 4.5 v to 5.5 v - - 0.8 v i i input leakage current v i = v cc or gnd; v cc = 5.5 v - - ? 1.0 ? a i s(off) off-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 1.0 ? a all channels - - ? 8.0 ? a
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 13 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer i s(on) on-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 --? 8.0 ? a i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd; v cc = 4.5 v to 5.5 v - - 80.0 ? a ? i cc additional supply current per input pin; v i = v cc ? 2.1 v; other inputs at v cc or gnd; v cc = 4.5 v to 5.5 v pin e - - 270 ? a pin sn - - 225 ? a t amb = ? 40 ? c to +125 ?c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 - - v v il low-level input voltage v cc = 4.5 v to 5.5 v - - 0.8 v i i input leakage current v i = v cc or gnd; v cc = 5.5 v - - ? 1.0 ? a i s(off) off-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 10 per channel - - ? 1.0 ? a all channels - - ? 8.0 ? a i s(on) on-state leakage current v cc = 5.5 v; v i = v ih or v il ; ?v sw ? = v cc ? gnd ; see figure 11 --? 8.0 ? a i cc supply current v i = v cc or gnd; v is = gnd or v cc ; v os =v cc or gnd; v cc = 4.5 v to 5.5 v - - 160 ? a ? i cc additional supply current per input pin; v i = v cc ? 2.1 v; other inputs at v cc or gnd; v cc = 4.5 v to 5.5 v pin e - - 294 ? a pin sn - - 245 ? a table 8. static characteristics 74hct4067 ?continued at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v). v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit v is = v cc and v os = gnd v is = gnd and v os = v cc v is = v cc and v os = open v is = gnd and v os = open fig 10. test circuit for measuring off-state leakage current fig 11. test circuit for measuring on-state leakage current i sw i sw 001aag734 v ih z v cc yn e v os v is gnd i sw 001aag735 v il zy n e v os v is gnd v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 14 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 11. dynamic characteristics table 9. dynamic characteristics 74hc4067 gnd = 0 v; t r = t f = 6 ns; c l = 50 pf unless specified otherwise; for test circuit see figure 14 . v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions 25 ?c ? 40 ? c to +125 ?c unit typ max max (85 ? c) max (125 ?c) t pd propagation delay yn to z; see figure 12 [1] [2] v cc = 2.0 v 25 75 95 110 ns v cc = 4.5 v 9 15 19 22 ns v cc = 6.0 v 7 13 16 19 ns v cc = 9.0 v 5 9 11 14 ns z to yn v cc = 2.0 v 18 60 75 90 ns v cc = 4.5 v 6 12 15 18 ns v cc = 6.0 v 5 10 13 15 ns v cc = 9.0 v 4 8 10 12 ns t off turn-off time e to yn; see figure 13 [3] v cc = 2.0 v 74 250 315 375 ns v cc = 4.5 v 27 50 63 75 ns v cc = 5.0 v; c l = 15 pf 27 - - - ns v cc = 6.0 v 22 43 54 64 ns v cc = 9.0 v 20 38 48 57 ns sn to yn v cc = 2.0 v 83 250 315 375 ns v cc = 4.5 v 30 50 63 75 ns v cc = 5.0 v; c l = 15 pf 29 - - - ns v cc = 6.0 v 24 43 54 64 ns v cc = 9.0 v 21 38 48 57 ns e to z v cc = 2.0 v 85 275 345 415 ns v cc = 4.5 v 31 55 69 83 ns v cc = 6.0 v 25 47 59 71 ns v cc = 9.0 v 24 42 53 63 ns sn to z v cc = 2.0 v 94 290 365 435 ns v cc = 4.5 v 34 58 73 87 ns v cc = 6.0 v 27 47 62 74 ns v cc = 9.0 v 25 45 56 68 ns
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 15 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer [1] t pd is the same as t phl and t plh . [2] due to higher z terminal capacitance (1 6 switches versus 1) the delay figures to the z terminal are higher than those to the y terminal. [3] t on is the same as t phz and t plz . [4] t off is the same as t pzh and t pzl . [5] c pd is used to determine the dynamic power dissipation (p d in ? w). p d = c pd ? v cc 2 ? f i + ? {(c l +c sw ) ? v cc 2 ? f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l +c sw ) ? v cc 2 ? f o } = sum of outputs; c l = output load capacitance in pf; c sw = switch capacitance in pf; v cc = supply voltage in v. t on turn-on time e to yn; see figure 13 [4] v cc = 2.0 v 80 275 345 415 ns v cc = 4.5 v 29 55 69 83 ns v cc = 5.0 v; c l = 15 pf 26 - - - ns v cc = 6.0 v 23 47 59 71 ns v cc = 9.0 v 17 42 53 63 ns sn to yn v cc = 2.0 v 88 300 375 450 ns v cc = 4.5 v 32 60 75 90 ns v cc = 5.0 v; c l = 15 pf 29 - - - ns v cc = 6.0 v 26 51 64 77 ns v cc = 9.0 v 18 45 56 68 ns e to z v cc = 2.0 v 85 275 345 415 ns v cc = 4.5 v 31 55 69 83 ns v cc = 6.0 v 25 47 59 71 ns v cc = 9.0 v 18 42 53 63 ns sn to z v cc = 2.0 v 94 300 375 450 ns v cc = 4.5 v 34 60 75 90 ns v cc = 6.0 v 27 51 64 77 ns v cc = 9.0 v 19 45 56 68 ns c pd power dissipation capacitance per switch; v i = gnd to v cc [5] 29 - - - pf table 9. dynamic characteristics 74hc4067 ?continued gnd = 0 v; t r = t f = 6 ns; c l = 50 pf unless specified otherwise; for test circuit see figure 14 . v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions 25 ?c ? 40 ? c to +125 ?c unit typ max max (85 ? c) max (125 ?c)
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 16 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer [1] t pd is the same as t phl and t plh . [2] due to higher z terminal capacitance (1 6 switches versus 1) the delay figures to the z terminal are higher than those to the y terminal. [3] t on is the same as t phz and t plz . [4] t off is the same as t pzh and t pzl . [5] c pd is used to determine the dynamic power dissipation (p d in ? w). p d = c pd ? v cc 2 ? f i + ? {(c l +c sw ) ? v cc 2 ? f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l +c sw ) ? v cc 2 ? f o } = sum of outputs; c l = output load capacitance in pf; c sw = switch capacitance in pf; v cc = supply voltage in v. table 10. dynamic characteristics 74hct4067 gnd = 0 v; t r = t f = 6 ns; c l = 50 pf unless specified otherwise; for test circuit see figure 14 . v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions 25 ?c ? 40 ? c to +125 ?c unit typ max max (85 ? c) max (125 ?c) t pd propagation delay yn to z; see figure 12 [1] [2] v cc = 4.5 v 9 15 19 22 ns z to yn v cc = 4.5 v 6 12 15 18 ns t off turn-off time e to yn; see figure 13 [3] v cc = 4.5 v 26 55 69 83 ns v cc = 5.0 v; c l = 15 pf 26 - - - ns sn to yn v cc = 4.5 v 31 55 69 83 ns v cc = 5.0 v; c l = 15 pf 30 - - - ns e to z v cc = 4.5 v 30 60 75 90 ns sn to z v cc = 4.5 v 35 60 75 90 ns t on turn-on time e to yn; see figure 13 [4] v cc = 4.5 v 32 60 75 90 ns v cc = 5.0 v; c l = 15 pf 32 - - - ns sn to yn v cc = 4.5 v 35 60 75 90 ns v cc = 5.0 v; c l = 15 pf 33 - - - ns e to z v cc = 4.5 v 38 65 81 98 ns sn to z v cc = 4.5 v 38 65 81 98 ns c pd power dissipation capacitance per switch; v i = gnd to (v cc ? 1.5 v) [5] 29 - - - pf
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 17 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 12. waveforms fig 12. input (v is ) to output (v os ) propagation delays 001aad555 t plh t phl 50 % 50 % v is input v os output measurement points are shown in table 11 . fig 13. turn-on an d turn-off times 001aad556 t plz t phz switch off switch on switch on v os output v os output e, sn inputs v m v i 0 v 90 % 10 % t pzl t pzh 50 % 50 % table 11. measurement points type v i v m 74hc4067 v cc 0.5v cc 74hct4067 3.0 v 1.3 v
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 18 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer [1] for 74hct4067: maximum input voltage v i = 3.0 v. test data is given in table 12 . definitions test circuit: r t = termination resistance should be equal to output impedance z o of the pulse generator. c l = load capacitance including jig and probe capacitance. r l = load resistor. s1 = test selection switch. fig 14. load circuitry for measuring switching times v m v m t w t w 10 % 90 % 0 v v i v i negative pulse positive pulse 0 v v m v m 90 % 10 % t f t r t r t f 001aag732 v cc v cc open gnd v i v os dut c l r t r l s1 pulse generator v is table 12. test data test input output s1 position control e address sn switch yn (z) t r , t f switch z (yn) v i [1] v i [1] v is c l r l t phl, t plh gnd gnd or v cc gnd to v cc 6ns 50pf - open t phz , t pzh gnd to v cc gnd to v cc v cc 6ns 50pf, 15pf 1k ? gnd t plz , t pzl gnd to v cc gnd to v cc gnd 6 ns 50 pf, 15 pf 1 k ? v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 19 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 13. additional dynamic characteristics [1] adjust input voltage v is to 0 dbm level (0 dbm = 1 mw into 600 ? ). [2] adjust input voltage v is to 0 dbm level at v os for f i = 1 mhz (0 dbm = 1 mw into 50 ? ). after set-up, f i is increased to obtain a reading of ? 3db at v os . table 13. additional dynamic characteristics recommended conditions and typical values; gnd = 0 v; t amb = 25 ? c. v is is the input voltage at a yn or z terminal, whichever is assigned as an input. v os is the output voltage at a yn or z terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit thd total harmonic distortion r l = 10 k ? ; c l = 50 pf; see figure 15 f i = 1 khz v cc = 4.5 v; v is(p-p) = 4.0 v - 0.04 - % v cc = 9.0 v; v is(p-p) = 8.0 v - 0.02 - % f i = 10 khz v cc = 4.5 v; v is(p-p) = 4.0 v - 0.12 - % v cc = 9.0 v; v is(p-p) = 8.0 v - 0.06 - % ? iso isolation (off-state) r l = 600 ? ; c l = 50 pf; see figure 16 [1] v cc = 4.5 v - ? 50 - db v cc = 9.0 v - ? 50 - db f (-3db) ? 3 db frequency response r l = 50 ? ;c l = 10 pf; see figure 17 [2] v cc = 4.5 v - 90 - mhz v cc = 9.0 v - 100 - mhz c sw switch capacitance independent pins y - 5 - pf common pin z - 45 - pf fig 15. test circuit for measuring total harmonic distortion 10 f 001aag736 v il z gnd yn e v os d v cc 2r l 2r l c l v is f i v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 20 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer a. isolation (off-state) b. test circuit v cc = 4.5 v; gnd = 0 v; r l = 600 ? ; r source = 1 k ? . fig 16. isolation (off-state) as a function of frequency 001aae332 f i (khz) 10 10 5 10 6 10 4 10 2 10 3 ?60 ?40 ?80 ?20 0 iso (db) ?100 0.1 f 001aag737 v ih z gnd yn e v os v cc 2r l 2r l c l v is f i db v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 21 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer a. typical ? 3 db frequency response b. test circuit v cc = 4.5 v; gnd = 0 v; r l = 50 ? ; r source = 1 k ? . fig 17. ? 3 db frequency response 001aag739 f i (khz) 10 10 5 10 6 10 4 10 2 10 3 0 5 v os (db) ?5 0.1 f 001aag738 v il z db yn e v os v cc 2r l 2r l c l v is f i gnd v cc
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 22 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 14. package outline fig 18. package outline sot101-1 (dip24) unit a max. 1 2 b 1 cd e e m h l references outline version european projection issue date iec jedec jeita mm inches dimensions (inch dimensions are derived from the original mm dimensions) sot101-1 99-12-27 03-02-13 a min. a max. b w m e e 1 1.7 1.3 0.53 0.38 0.32 0.23 32.0 31.4 14.1 13.7 3.9 3.4 0.25 2.54 15.24 15.80 15.24 17.15 15.90 2.2 5.1 0.51 4 0.066 0.051 0.021 0.015 0.013 0.009 1.26 1.24 0.56 0.54 0.15 0.13 0.01 0.1 0.6 0.62 0.60 0.68 0.63 0.087 0.2 0.02 0.16 051g02 mo-015 sc-509-24 m h c (e ) 1 m e a l seating plane a 1 w m b 1 e d a 2 z 24 1 13 12 b e pin 1 index 0 5 10 mm scale note 1. plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. z max. (1) (1) (1) dip24: plastic dual in-line package; 24 leads (600 mil) sot101-1
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 23 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 19. package outline sot137-1 (so24) unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p q z ywv references outline version european projection issue date iec jedec jeita mm inches 2.65 0.3 0.1 2.45 2.25 0.49 0.36 0.32 0.23 15.6 15.2 7.6 7.4 1.27 10.65 10.00 1.1 1.0 0.9 0.4 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.1 0.4 sot137-1 x 12 24 w m a a 1 a 2 b p d h e l p q detail x e z c l v m a 13 (a ) 3 a y 0.25 075e05 ms-013 pin 1 index 0.1 0.012 0.004 0.096 0.089 0.019 0.014 0.013 0.009 0.61 0.60 0.30 0.29 0.05 1.4 0.055 0.419 0.394 0.043 0.039 0.035 0.016 0.01 0.25 0.01 0.004 0.043 0.016 0.01 e 1 0 5 10 mm scale so24: plastic small outline package; 24 leads; body width 7.5 mm sot137-1 99-12-27 03-02-19
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 24 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 20. package outline sot340-1 (ssop24) unit a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm 0.21 0.05 1.80 1.65 0.38 0.25 0.20 0.09 8.4 8.0 5.4 5.2 0.65 1.25 7.9 7.6 0.9 0.7 0.8 0.4 8 0 o o 0.13 0.1 0.2 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.2 mm maximum per side are not included. 1.03 0.63 sot340-1 mo-150 99-12-27 03-02-19 x w m a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 11 2 24 13 0.25 y pin 1 index 0 2.5 5 mm scale ssop24: plastic shrink small outline package; 24 leads; body width 5.3 mm sot340-1 a max. 2
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 25 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 21. package outline sot355-1 (tssop24) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 7.9 7.7 4.5 4.3 0.65 6.6 6.2 0.4 0.3 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot355-1 mo-153 99-12-27 03-02-19 0.25 0.5 0.2 w m b p z e 11 2 24 13 pin 1 index a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a d y 0 2.5 5 mm scale tssop24: plastic thin shrink small outline package; 24 leads; body width 4.4 mm sot355-1 a max. 1.1
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 26 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer fig 22. package outline sot815-1 (dhvqfn24) references outline version european projection issue date iec jedec jeita note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. sot815-1 - - - - - - - - - 03-04-29 sot815-1 0 2.5 5 mm scale b y y 1 c c ac c b v m w m e 1 e 2 terminal 1 index area terminal 1 index area x unit a (1) max. a 1 bc e e h l e 1 ywv mm 1 0.05 0.00 0.30 0.18 0.5 4.5 e 2 1.5 0.2 2.25 1.95 d h 4.25 3.95 0.05 0.05 y 1 0.1 0.1 dimensions (mm are the original dimensions) 0.5 0.3 d (1) 5.6 5.4 e (1) 3.6 3.4 d e b a e dhvqfn24: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 24 terminals; body 3.5 x 5.5 x 0.85 mm a a 1 c detail x e h l d h 2 23 11 14 13 12 1 24
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 27 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 15. revision history table 14. revision history document id release date data sheet status change notice supersedes 74hc_hct4067 v.5 20111213 product data sheet - 74hc_hct4067 v.4 modifications: ? legal pages updated. 74hc_hct4067 v.4 20110518 product data sheet - 74hc_hct4067 v.3 74hc_hct4067 v.3 20071015 product data sheet - 74hc_hct4067_cnv v.2 74hc_hct4067_cnv v.2 19970901 product specification - -
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 28 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer 16. legal information 16.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 16.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 16.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. export control ? this document as well as the item(s) described herein may be subject to export control regulations. export might require a prior authorization from competent authorities. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
74hc_hct4067 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2011. all rights reserved. product data sheet rev. 5 ? 13 december 2011 29 of 30 nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. 16.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 17. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors 74hc4067; 74hct4067 16-channel analog multiplexer/demultiplexer ? nxp b.v. 2011. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 13 december 2011 document identifier: 74hc_hct4067 please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 18. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 6 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 7 functional description . . . . . . . . . . . . . . . . . . . 7 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 7 9 recommended operating conditions. . . . . . . . 8 10 static characteristics. . . . . . . . . . . . . . . . . . . . . 9 11 dynamic characteristics . . . . . . . . . . . . . . . . . 14 12 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 13 additional dynamic characteristics . . . . . . . . 19 14 package outline . . . . . . . . . . . . . . . . . . . . . . . . 22 15 revision history . . . . . . . . . . . . . . . . . . . . . . . . 27 16 legal information. . . . . . . . . . . . . . . . . . . . . . . 28 16.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 28 16.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 16.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 16.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 29 17 contact information. . . . . . . . . . . . . . . . . . . . . 29 18 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

▲Up To Search▲

Price & Availability of 74HC4067BQ

	To Download 74HC4067BQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .